SYSTEM FEATURES

For lowest weight and highest robustness we have designed the drone completely in carbon fiber reinforced plastics. This carbon mono frame is also a perfect shield against electromagnetic interferences.

Our outstanding AAHRS (Altitude and Attitude and Heading Reference System) uses the following sensor types: Accelerometers, Gyroscopes, Magnetometer, Air pressure, Humidity, Temperature.

By means of our synchronized, brushless direct drives (transmission less) the noise level is very low (rpm < 2000, noise < 63dBA @3m). These propulsions recover from stall and overload conditions even at flight time.

The optional GPS provides position hold and autonomous waypoint navigation.  

Our onboard flight recorder (microSD card) permits a post-flight analysis in real-time.

With our downlink decoder we provide all important data at the base station (battery state, altitude, attitude, position, flight time...).
For best pilot support we have implemented a talking audio response system (no need to look at a display).

Security features prevent from crashing - autonomous landing on low battery or missing radio signal.

Depending on payload, temperature and wind the vehicle achieves up to 20 minutes of flight time.

By means of our software tools we provide a worldwide accessible service consisting of remote diagnostics and firmware updates.


 

 

M1.0 micro drone set, Ready-To-Fly

1x md4-200 High endurance 4-rotor VTOL, Complete carbon design, Flight controller, Navigation controller, Gearless brushless motors, Dual conversion FM-receiver, Landing gear, Antenna, Attitude / Altitude control, Flight duration approx. 20 min, 200g Payload, Diameter < 1m, Security features, Low noise (< 63dBA @3m), Water-protected with IO-controller, 5V/1A supply, 2x Standard servo, 2x Switch channel 5V/16V, 1A load, RS-232 extension for zoom camera and other special equipment

1x Afmtx13 FM-synthesizer transmitter 13-channel, 35/40/41MHz

3x Acb370ccw Carbon blade, 370mm (front and rear motor)

3x Acb370cw Carbon blade, 370mm (left and right motor)

2x Abat4s2.3 LIPO battery 4s, 14.8V, 2300mAh

1x Peli case, Dimensions 800 x 581 x 479mm

B1.0 Base station set

1.4 Megapixel video eyeglasses

2.4 GHz 4-fold antenna diversity receiver

Internal power supply, Inputs: 230/115VAC, 12/14.8VDC

Alcb4 LiPo Charger and true single cell balancer

USB video frame grabber, Video splitter 3x out

Downlink decoder for receiving the complete machine state (Battery, Receiver quality, RC-signals, Attitude, Altitude, GPS-position, Flight time etc.).

Base station software "mdCockpit"

2x Abat4s2.3 LIPO battery 4s, 14.8V, 2300mAh (same as M1.0)

 

1x Peli case (fits into M1.0), Dimensions 486 x 392 x 192mm

(Notebook not included)

Pdcvc470 Daylight color video camera, Composite video, 470 TV-Lines, Tilt controlled mount

Pdbwvc570 Dawn b/w video camera, Composite video, 570 TV-Lines, 0.0003 Lux, f1.4, Tilt controlled mount
Ppdc10mp Still photography, 10mp (3648x 2736 Pixel), Picture stabilization, 1GB Memory card, Infrared trigger, Tilt controlled mount .
Ogpsmag GPS-position hold, Carbon fiber cap with integrated GPS antenna / receiver, 3D-magnetometer, Firmware extension
Alcb4 LiPo Charger with true single cell balancer, Supply 12VDC, Maximal load current 3.1A

Acb370ccw Carbon blade, 370mm (front and rear motor)

Acb370cw Carbon blade, 370mm (left and right motor)